News
Position:
Home
/
/
/
How to maintain and maintain the baler from time to time

How to maintain and maintain the baler from time to time

  • Categories:Company News
  • Author:
  • Origin:
  • Time of issue:2018-12-22
  • Views:122

(Summary description)The four points that the baler needs to be maintained: 1. Adjust the bundling tightness of the mechanical baling material of Bohong baling belt. Open the table top, loosen the hexagon socket set screw on the top of Daluomu A by hand, and turn it clockwise to tighten, and vice versa. for pine. After the binding force is moderate, tighten the hexagon socket set screw. 2. Adjustment of belt width and joint opening. When the belt width is uneven or the belt of another width is replaced, the left and right belt insertion slots must be adjusted. If the slot is too narrow, the belt insertion will be difficult; if it is too wide, the belt will be joined after baling There will be misalignment. Generally, the width of the slot should be about 0.5-1 mm wider than the width of the belt. 3. Adjust the temperature of the ironing head of the baler

How to maintain and maintain the baler from time to time

(Summary description)The four points that the baler needs to be maintained: 1. Adjust the bundling tightness of the mechanical baling material of Bohong baling belt. Open the table top, loosen the hexagon socket set screw on the top of Daluomu A by hand, and turn it clockwise to tighten, and vice versa. for pine. After the binding force is moderate, tighten the hexagon socket set screw. 2. Adjustment of belt width and joint opening. When the belt width is uneven or the belt of another width is replaced, the left and right belt insertion slots must be adjusted. If the slot is too narrow, the belt insertion will be difficult; if it is too wide, the belt will be joined after baling There will be misalignment. Generally, the width of the slot should be about 0.5-1 mm wider than the width of the belt. 3. Adjust the temperature of the ironing head of the baler

  • Categories:Company News
  • Author:
  • Origin:
  • Time of issue:2018-12-22
  • Views:122
Information

Four points that balers need to be maintained:

1. Adjust the strapping tightness of the mechanical packing material of the packing belt. Open the table top, loosen the hexagon socket set screw on the top of the big Luomu A by hand, and turn it clockwise to tighten it, and vice versa. After the binding force is moderate, tighten the hexagon socket set screw.

2. Adjustment of strap width and joint opening When the strap width is uneven or the strap is replaced with another width, the left and right strap insertion slots must be adjusted. If the slot is too narrow, it will be difficult to insert the strap; if it is too wide, the strap will be joined after baling There will be misalignment. Generally, the width of the slot should be about 0.5-1 mm wider than the width of the belt.

3. Adjusting the temperature of the ironing head of the baler The temperature of the ironing head has a great influence on the quality of the strap joint. Whether the temperature of the ironing head is appropriate, you can check the adhesion of the surface of the ironing head. If there are white marks on the surface of the ironing head, the temperature is too high. If the surface of the ironing head is wet, the temperature is insufficient.

4. Feeding belt length adjustment The length of the feeding belt is determined by the feeding belt length adjuster on the front panel. If the strap is too short, it is easy to tie the hand. At this time, the baler can use the hand to grasp the head of the strap and pull the strap along the feeding direction. However, it is necessary to re-adjust the length of the conveyor belt to ensure the normal progress of the next bundling.

If the strap is too long, it is not easy to align the position, and the straps of the baler and Panasonic are easy to wrap together and cause the strap to be misaligned or broken. Packaging machinery requires frequent maintenance:

1. When refueling, do not add too much to prevent the micro switch from malfunctioning due to oil immersion. (It should be noted that these parts cannot be refueled: send and return belt rollers. All belts. Slipper and surrounding.)

2. Once a week, remove crumbs or dirt from the machine.

3. Clean, maintain and lubricate the upper slide plate, middle knife and front top knife mentioned in the previous section once a month.

4. Once every three months, after the above two maintenances have been done, add some lubricating oil to all (shaft, core) and bearings.

5. Replenish the oil in the reducer wheel box every two years.

Scan the QR code to read on your phone

There is currently no information to display
Please add data record on website background.
There is currently no information to display
Please add data record on website background.

Information

Service Hotline: +86 13867343586

Fax: +86-573-86760618

Email: admin@jxhdbz.cn

Add:Huangqiao Industrial Zone,Yucheng Town,Haiyan County, Jiaxing ,Zhejiang ,China

Copyright © Zhejiang Hongda Packaging Technology Co.,Ltd.    浙ICP备16031742号-1号 

Powered by:www.300.cn

Copyright © Zhejiang Hongda Packaging Technology Co.,Ltd. 

浙ICP备16031742号-1号

www.300.cn